Defrost Timer – 60Hz 120V Specifications This Defrost Timer works like a clock by switching on the defrost heater circuit after a predetermined amount of compressor run time. This allows the defrost circuit to clear the evaporator of ice or frost to maintain proper airflow. The defrost timer is located in the control housing which is in the refrigerator section of your appliance. If this part is not working, it can lead to temperature increases in your refrigerator. If the compressor circuit fails, no cooling will take place; if the defrost circuit isn’t activated, ice will quickly build up on the evaporator coils and reduce airflow and efficiency. If the timer doesn’t advance or if the contacts have no continuity, the timer will need to be replaced. This timer measures approximately 3 inches long and 5 inches wide, and is constructed of plastic and metal. It comes in black/white/silver and is sold individually. This replacement part features 1 defrost timer.
Troubleshooting How Buying OEM Parts Can Save You Time and Money This part resolves the following issues: Fridge too warm; Freezer not defrosting; Freezer section too warm; Will Not Start This part is compatible with the following products: Refrigerator; Freezer; Air Conditioner; Washing Machine; and Dryer. The following products are compatible with this part: Frigidaire, Kenmore, Gibson, and Kelvinator Part# 215846602 replaces these: AP2111929, 12762, 215846602, 00624728, 00626234, 00628510, 00628518, 0628510, 08000559, 08006054, 08006992, 08016919, 08950148, 215267800, 215846605, 215846606, 240371001, 241621501, 3001671, 3001701.
Ask a question about this section to our experts, and we’ll respond as soon as we can!
Hi Terri, Thank you for the question. Sounds like you need to replace the Defrost Timer. The defrost circuit in your refrigerator and freezer includes defrost timers. This timer cycles the defrost heater on and off. The appliance timer will cycle for 30 minutes every eight hours. The defrost heater can stop your freezer from frosting up by melting the frost accumulation on the evaporator coils. If your timer malfunctions, the heater won’t get the power it needs to run, and frost will continue to accumulate, raising the fridge’s temperature. Hope this helps!.
Hello Harry, that is a great question. No, you don’t need to set the defrost timer; once it’s installed, just turn the power back on, and everything should work as it should. Hope this helps!.
Hi Terri, Thank you for the question. Using a multimeter, you can check the defrost heater and thermostat. If they are in good working order, the defrost timer is probably the problem. Additionally, it is wise to inspect the door gasket. You can place a flash light inside the refrigerator and shut the door in the dark to check for light leaks around the gasket. Hope this helps!.
Hi Greg, Thank you for the question. At the bottom of the appliance, under your model number, is where the defrost timer is located. Open the door if necessary, then take the kick plate grill off. There will be a cover you can remove to reveal the timer in the bottom left corner. Hope this helps!.
Hello Michael, thank you for contacting us. The fridge components may just need a good cleaning. Any dust or debris should be removed from the coils near the compressor and condenser fan at the back of the refrigerator. While the panel is off, you can check the evaporator fan, which circulates cool air into the refrigerator, to make sure it is functioning properly. You can also remove the panel in the freezer to ensure that the coils there are not iced up. The thermostat or the defrost timer, as you mentioned, are other possibilities. The thermostat can be tested with a multi-meter. Hope this helps!.
Hello Sam, thank you for contacting us. You can access and replace that timer by watching our how-to video on our YouTube channel. We sincerely hope the link below will be of assistance. youtube. com/watch?v=kKYvssvclvA.
Hi Frank, Thank you for your question. There may be a few components involved in your problem, but since warmth is present in both your fridge and freezer compartments, I would also advise testing your defrost timer, defrost thermostat, run capacitor, and start relay. I hope that helps. Good luck with your repair.
Hi Matt, Thank you for the question. I suggest testing the Run Capacitor, PartSelect Number PS2333670. When testing your capacitor set your meter to 1000 ohms. Your capacitor needs to be replaced if your meter continuously reads 0. Hope this helps!.
Hello Jesse, Thanks for your question. Several different factors could cause this kind of problem to occur. You should use a multimeter to check the electrical continuity of the temperature control and defrost thermostats. Replace them if they do not show continuity. I hope this helps.
Hi Chris, Thank you for the question. I advise replacing the Run Capacitor, PartSelect Number PS2333670, if the appliance runs too long. Your refrigerator and freezer will stay at a constant temperature thanks to the run capacitor, which assists the compressor in starting and stopping. Hope this helps!.
Customer Repair Stories Average Repair Rating: 3. 8 / 5. 0, 68 reviews.
Stephen from Warrington, PA 
Difficulty Level: Easy 
Total Repair Time: 30 – 60 mins 
Tools: Nutdriver, Pliers, Screw drivers Roger from Orangevale, CA Difficulty Level: Really Easy Total Repair Time: 15 – 30 mins Tools: Nutdriver, Screw drivers Juan from Riverside, CA Difficulty Level: Easy Total Repair Time: 15 – 30 mins Tools: Nutdriver, Pliers, Screw drivers, Socket set Michael from Newark, OH Difficulty Level: A Bit Difficult Total Repair Time: 1- 2 hours Tools: Nutdriver Mark from Tallahassee, FL Difficulty Level: Really Easy Total Repair Time: 15 – 30 mins Tools: Nutdriver, Screw drivers Marc from Sumas, WA Difficulty Level: Easy Total Repair Time: 1- 2 hours Tools: Screw drivers, Socket set Tad from Lancaster, OH Difficulty Level: Easy Total Repair Time: 15 – 30 mins Tools: Screw drivers Ronald from Bridgeport, CT Difficulty Level: Easy Total Repair Time: 15 – 30 mins Tools: Nutdriver, Pliers, Screw drivers Raymond T from New York, NY Difficulty Level: Easy Total Repair Time: 15 – 30 mins Tools: Nutdriver, Screw drivers Patrick from Gansevoort, NY Difficulty Level: A Bit Difficult Total Repair Time: 30 – 60 mins Tools: Nutdriver, Pliers